Get in Touch

267 Union Street

Suite 2

Hackensack NJ 07601

(201) 632 - 1055

hackensackgaragedoorco@gmail.com

Hours of Opperation

Monday: 12noon - 10pm

Tuesday: 12noon - 10pm

Wednesday: 12noon - 10pm

Thursday: 12noon - 10pm

Friday: 12noon - 10pm

Sat & Sun: 8am - 10pm

Service Area

Bergen County Guaranteed Garage Door Repair Co. offers garage door service and garage door repairs in:

  • Hackensack, NJ

  • Teaneck, NJ

  • River Edge, NJ

  • Maywood, NJ

  • Oradell, NJ

  • Bergenfield, NJ

  • Ridgewood, NJ

  • Paramus, NJ

  • Emerson, NJ

  • New Milford, NJ

  • Haworth, NJ

  • Closer, NJ

  • Ho-Ho-Kus

  • Saddle River

  • Woodcliff Lake

  • Clifton, NJ

  • Rutherford, NJ

  • East Rutherford, NJ

  • Elmwood Park, NJ

  • Hawthorne, NJ

  • Fairlwan, NJ

  • Glen Rock, NJ

  • Garfield, NJ

  • Lodi, NY

  • Rochelle Park, NJ

  • Englewood, NJ

  • Tenafly, NJ

  • Hillsdale, NJ

  • Westwood, NJ

  • Cresskill, NJ

© 2019 Website. com by Bergen County Garage Door Repair Co. . Proudly created by APNcare

25 Point Inspection

Garage Door Inspection Checklist

Bergen County Garage Doors offer a 25 Point Inspection Service to residential homes across Bergen County. With our 25 Point Inspection lube and tune service executed by our experienced technicians, your garage door systems is fully evaluated. Each component of your garage door is thoroughly checked to ensure a your garage door runs smoothly, efficiently, and safely. 

1. Door balance. This ensures the spring(s) are fully functionally.

2. Rollers. Quality Garage Door inspect every roller for signs of wear and tear, or damage.

3. Cables. Cables are inspected for fraying and kinking, which leads to damage.

4. Drums. Drum are looked over unusual defects and cracking.

5. Center Bearing. Inspection for wear and tear or burned out bearings is executed by Quality Garage Door. There are generally 2 types of center bearings; a single piece nylon bearing and a metal housing with actual ball bearings.

6. Center Bracket. Center brackets are inspected for signs of bending and other anomalies.

7. End Bearing Plates. The bearings allow the spring bar to turn freely as the door opens and closes. We check to make sure there are no faults.

8. Spring Bar. We inspect for rust and bending. The spring bar holds the springs and turns as the door opens and closes.

9. Hinges. Hinges are inspected for damage and excessive wear.

10. Top Brackets. Top brackets hold the top roller in place, and meticulously inspected.

11. Bottom Brackets. Bottom brackets are mounted on the lower garage door and hold the bottom rollers in place. These brackets contribute to the lifting point on the garage door.

12. Vertical Tracks. Bending and damage can occur; we check them to ensure they are up to par.

13. Horizontal Track. We also inspect for bending and damage.

14. Jamb Brackets. Jamb brackets attach the vertical tracks to the frame work on each side of the garage door opening, our Inspection searches for position, bending and other damage.

15. Strut. Struts are added supports for the garage door structure. Struts may be added if damage requires additional struts for support.

16. Weather Seal. Weather seals are rubber located at the bottom of the garage door. This seal helps prevent wind and windblown objects from entering the garage. 

17. Section (interior/exterior). We check for any dents, tearing in the metal along with any other damage.

18. Opener Controls. Controls are inspected for functioning efficiency.

19. Opener Trolley/Carriage. Inspected for damage and grinding in screw drive openers.

20. Safety Eyes. The safety eyes keep the door from closing if a person or object is in the garage doors path. 

21. Motor Gears. Motor gears are susceptible to wear and tear in belt and chain drive so we look for proper tension and sign of deterioration.

22. Wires. Visually inspected for any signs of wear and tear or cracking in the wire coating.

23. Limits. Check the limits to ensure the door opens and closes to the proper travel locations.

24. Opening/Closing Force. We test the force limits to ensure there is proper force being applied to the door during opening and closing.

25. Springs. Finally, we visually inspect the springs for signs of rust and deterioration. We also measure each spring to make sure they are adequate.